We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
Heat transfer oils are designed to move fast and transfer maximum heat at high temperatures. However, the properties such as high density and low viscosity, besides optimizing these performance characteristics, make it difficult to retain the fluids’ molecules at operating temperatures. These particular properties, which make the fluids better heat transfer media, also make them susceptible to leakage.
Smoke emanating upon exposure of the hot fluid to air is a simple leak detector for thermal fluids. Criteria such as the size of the leak, the fluid temperature, and to a certain degree the airflow in the area determine the amount of smoke. In the case of minor oozing leaks, an enormous amount of smoke is generated as there is no adequate fluid for drop formation. Such a steady seepage causes smoking and then gets accumulated onto the metal close to the leak, thereby leaving dark stains, or a carbon crust over time.
In the case of larger leaks, the fluid normally gets cooled quickly as it is dripped or sprayed into the air. As smoke is caused by the reaction of the volatile low-boiling portions, i.e. smaller molecules, of the heat transfer fluid with the oxygen in air, the cooling minimizes the fluid vaporization, thereby reducing the amount of smoke. Nevertheless, if the leak is large enough for its oxidation to use up all the fresh air, or in cases where ventilation is inadequate, the vapor may get accumulated and lead to a probable fire hazard.
A major solution for avoiding safety issues due to leaks is to ensure that thermal fluid systems are not operated in enclosed areas that have insufficient ventilation. If there are chances for a considerable amount of leak, sufficient amount of fresh air flow must be ensured in such locations, e.g. valves, pumps, flanges, instrument ports, expansion tanks.
The flammability conditions of hydrocarbon liquids and their vapors are described by three major technical terms: autoignition temperature, fire point, and flash point.
Autoignition temperature is the temperature at which the vapor formed by a heated liquid flashes even in the absence of an ignition source.
Fire point is defined as the lowest temperature at which the vapor/air mixture of a heated liquid continuously burns when the ignition is supported by an ignition source that is placed above the liquid surface, or by a spark or flame.
Flash point is the lowest temperature at which the vapor/air mixture of a heated liquid can be ignited, i.e. “flashed,” by ignition sources such as those mentioned above.
The to-be-tested liquid is taken in a cup and heated. The increase in liquid temperature is continuously measured. A small flame is made to mechanically move to and fro just above the liquid surface. Once the temperature of the liquid increases, more liquid gets evaporated and causes the concentration of vapor/air mixture above the liquid to slowly increase. Once the lower flammability limit is attained, the vapor/air mixture is ignited by the ignition source, thus causing a pop. The observed temperature at which the flame immediately ignites the vapor/air mixture is the flashpoint. The ignition is repeated along with an increase in the liquid temperature. The observed temperature at which the burning turns continuous is the fire point.
A flask containing the sample is heated to the test temperature. The temperature at which a “flash” is observed in the container is the autoignition temperature. Upon observing no flash even after a specific period of time, the test is repeated by increasing the flask temperature. However, this method, i.e. ASTM E659-78, is valid only in the case of fluids that get entirely vaporized at the test temperature because the test result may be affected by the degradation products formed from any leftover liquid.
The following three conditions should be satisfied for the occurrence of a flash-point-related fire:
Natural or synthetic heat transfer fluids in closed-loop systems are regularly used well in excess of their fire and flashpoints.
This information has been sourced, reviewed and adapted from materials provided by Paratherm.
For more information on this source, please visit Paratherm.
Please use one of the following formats to cite this article in your essay, paper or report:
Paratherm. (2022, May 19). Detection and Prevention of Leaks in Thermal Fluid System. AZoM. Retrieved on August 20, 2022 from https://www.azom.com/article.aspx?ArticleID=12857.
Paratherm. "Detection and Prevention of Leaks in Thermal Fluid System". AZoM. 20 August 2022. <https://www.azom.com/article.aspx?ArticleID=12857>.
Paratherm. "Detection and Prevention of Leaks in Thermal Fluid System". AZoM. https://www.azom.com/article.aspx?ArticleID=12857. (accessed August 20, 2022).
Paratherm. 2022. Detection and Prevention of Leaks in Thermal Fluid System. AZoM, viewed 20 August 2022, https://www.azom.com/article.aspx?ArticleID=12857.
Do you have a question you'd like to ask regarding this article?
At the Advanced Materials Show 2022, AZoM caught up with the CEO of Cambridge Smart Plastics, Andrew Terentjev. In this interview, we discuss the company's novel technologies and how they could revolutionize how we think about plastics.
At the Advanced Materials Show in June 2022, AZoM spoke with Ben Melrose from International Syalons about the advanced materials market, Industry 4.0, and efforts to move toward net-zero.
At the Advanced Materials Show, AZoM spoke with Vig Sherrill from General Graphene about the future of graphene and how their novel production technique will lower costs to open up a whole new world of applications in the future.
This product profile describes the Flex Raman Catalog.
This is the full list of rotary evaporators offered by IKA Werke.
This product from Alicona features Cobots, which consist of a collaborative 6-axis robot and optical 3D measuring sensors to provide user-friendly measurement automation.
AZoM.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2022